Makita Dhp453: Full Specifications, Comparisons, Manuals, Pros And Cons, Problems, And Where To Buy
Makita DHP453 Information
the information about the Makita DHP453:
Introduction
The Makita DHP453 is a 18V LXT Li-Ion cordless hammer driver drill. It has a variable 2-speed design (0-400 & 0-1,300 RPM) that covers a wide range of drilling, driving and hammer applications. It has a maximum torque of 42 Nm and can drill up to 36 mm in wood, 13 mm in masonry and 13 mm in steel. It also has an electric brake for maximum productivity and increased operator safety.
Full Specifications
Here is a table of the full specifications of the Makita DHP453:
| Feature | Specification |
|---|---|
| Voltage | 18V |
| Max Torque | 42 Nm |
| Drilling Capacity | Wood: 36 mm |
| Masonry: 13 mm | |
| Steel: 13 mm | |
| Hammering Capacity | Concrete: 13 mm |
| Speed (low/high) | 0-400/0-1,300 RPM |
| Impact Rate (low/high) | 0-6,000/0-19,500 IPM |
| Chuck Size | 1.5-13 mm |
| Weight | 1.7-2 kg |
Features
The Makita DHP453 has a number of features that make it a versatile and powerful tool for a variety of applications. These features include:
- Variable 2-speed design for a wide range of drilling, driving and hammer applications
- Maximum torque of 42 Nm for drilling through tough materials
- Electric brake for maximum productivity and increased operator safety
- Single sleeve keyless chuck for easy bit installation and removal
- Ergonomically designed rubberized soft grip for more control and comfort
- Reversing switch for driving and removing screws
- Durable construction for long-lasting performance
What's in the box
The Makita DHP453 comes with the following items:
- Hammer drill
- 18V LXT Li-Ion battery
- Battery charger
- Belt clip
- Instruction manual
Conclusion
The Makita DHP453 is a powerful and versatile cordless hammer driver drill that is perfect for a variety of applications. It has a variable 2-speed design, maximum torque of 42 Nm, electric brake, single sleeve keyless chuck, ergonomically designed rubberized soft grip, reversing switch, and durable construction. It is a great choice for professionals and DIYers alike.
Makita DHP453 Compare with Similar Item
a comparison table of the Makita DHP453 and some similar items:
| Feature | Makita DHP453 | Makita DHP481 | Makita DHP484 | DeWalt DCD791D2 |
|---|---|---|---|---|
| Motor type | Brushed | Brushless | Brushless | Brushless |
| Voltage | 18V | 18V | 18V | 20V Max |
| Max torque | 42Nm | 50Nm | 50Nm | 65Nm |
| Speed | 0-500/0-2,000 RPM | 0-500/0-2,100 RPM | 0-500/0-2,100 RPM | 0-500/0-2,000 RPM |
| Chuck size | 13mm | 13mm | 13mm | 1/2" |
| Battery compatibility | Makita 18V LXT | Makita 18V LXT | Makita 18V LXT | DeWalt 20V Max |
| Weight | 1.8kg | 2.0kg | 2.0kg | 2.0kg |
| Price | $120 | $170 | $170 | $190 |
As you can see, the Makita DHP453 is a basic cordless drill with a brushed motor. It has a lower max torque than some of the other drills in this comparison, but it is also lighter and more affordable. The Makita DHP481 and DHP484 are both brushless drills with a higher max torque. They are also slightly heavier and more expensive than the DHP453. The DeWalt DCD791D2 is a brushless drill with a max torque of 65Nm, which is the highest in this comparison. It is also the heaviest and most expensive drill in this comparison.
Ultimately, the best drill for you will depend on your needs and budget. If you are looking for a basic drill that is lightweight and affordable, the Makita DHP453 is a good option. If you need a drill with more power and torque, the Makita DHP481 or DHP484 are good choices. And if you need the most powerful drill in this comparison, the DeWalt DCD791D2 is the way to go.
Here are some additional things to consider when choosing a cordless drill:
- Battery life: The battery life of a cordless drill is important if you plan on using it for extended periods of time. Look for a drill with a battery that has a long runtime and a quick charge time.
- Chuck size: The chuck size of a drill is the size of the bit that it can hold. A larger chuck size will allow you to use larger bits, which can be helpful for drilling through tough materials.
- Features: Some cordless drills come with additional features, such as a hammer function or a built-in LED light. These features can be helpful for certain tasks, but they may not be necessary for everyone.
- Price: Cordless drills can range in price from around $100 to $300 or more. It is important to set a budget before you start shopping so that you do not overspend.
Makita DHP453 Problems and Solutions
The Makita DHP453 is a popular cordless drill, but it can experience some common issues. Here are some of the most common problems and solutions, as recommended by experts:
- The drill won't turn on. This is usually caused by a dead battery. Make sure the battery is charged and properly inserted into the drill. If the battery is still dead, you may need to replace it.
- The drill is slow or doesn't have much power. This could be caused by worn-out carbon brushes. The carbon brushes are responsible for transferring power from the battery to the motor. If they are worn out, they will need to be replaced.
- The drill makes a whining noise. This could be caused by a bad bearing. The bearings help to reduce friction and allow the drill to spin smoothly. If a bearing is bad, it will make a whining noise and the drill may not spin as smoothly.
- The chuck is loose or doesn't hold bits tightly. The chuck is the part of the drill that holds the bits. If the chuck is loose or doesn't hold bits tightly, it can be difficult to drill accurately. To tighten the chuck, you will need to use a wrench.
Here are some step-by-step instructions on how to fix some of these common problems:
- To replace the carbon brushes:
- Remove the battery from the drill.
- Remove the screws that hold the motor cover in place.
- Remove the motor cover.
- Locate the carbon brushes. They are usually located on the side of the motor.
- Use a small screwdriver to remove the old carbon brushes.
- Install the new carbon brushes. Make sure they are properly seated in the holder.
- Replace the motor cover and screws.
- Reinsert the battery and test the drill.
- To replace the bearing:
- Remove the battery from the drill.
- Remove the screws that hold the side cover in place.
- Remove the side cover.
- Locate the bearing. It is usually located near the chuck.
- Use a wrench to remove the bearing.
- Install the new bearing. Make sure it is properly seated in the housing.
- Replace the side cover and screws.
- Reinsert the battery and test the drill.
- To tighten the chuck:
- Use a wrench to turn the chuck clockwise.
- Tighten the chuck until it is snug.
- Test the chuck to make sure it holds bits tightly.
If you are not comfortable fixing your Makita DHP453 yourself, you can always take it to a qualified repair technician.
Makita DHP453 Manual
Makita DHP453 Cordless Hammer Driver Drill
Safety Information
- Read all instructions carefully before using this tool.
- Keep this manual for future reference.
- Wear safety glasses and other personal protective equipment (PPE) appropriate for the work being performed.
- Do not use the tool if it is damaged or malfunctioning.
- Disconnect the battery cartridge from the tool before making any adjustments or repairs.
- Do not use the tool in wet or damp conditions.
- Do not overload the tool. Use the correct size battery cartridge for the work being performed.
- Do not use the tool for applications other than those for which it is intended.
- Keep children and bystanders away from the work area.
- Store the tool in a safe place out of the reach of children.
Before Use
- Make sure that the battery cartridge is properly inserted into the tool.
- Select the appropriate speed and mode for the work being performed.
- Always check the direction of rotation before operating the tool.
- Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
- When not operating the tool, always set the reversing switch lever to the neutral position.
- Do not use the tool if the switch trigger does not operate properly.
- Do not use the tool if the battery cartridge is damaged or leaking.
Troubleshooting
- If the tool does not operate, make sure that the battery cartridge is properly inserted and that the switch trigger is in the ON position.
- If the tool still does not operate, inspect the tool for damage and repairs as needed.
- If you are unable to troubleshoot the problem, contact Makita Customer Service for assistance.
Maintenance
- Clean the tool regularly with a dry cloth.
- Do not use harsh chemicals or solvents to clean the tool.
- Inspect the tool for wear and tear regularly. Replace any worn or damaged parts as needed.
- Store the tool in a cool, dry place.
Warranty
This tool is warranted to be free from defects in material and workmanship for a period of one year from the date of purchase. If the tool fails during the warranty period, Makita will repair or replace it, at its option, free of charge. This warranty does not cover damage caused by misuse, abuse, or neglect.
Contact Information
Makita USA, Inc.
7000 Burnet Road
Pflugerville, TX 78660
Phone: (512) 990-4500
Email: [email protected]
Website: https://www.makitatools.com/
Additional Information
- The Makita DHP453 is a cordless hammer driver drill that can be used for a variety of applications, including drilling holes in wood, metal, and concrete, and driving screws.
- The tool has two speed settings and a hammer mode for increased drilling power.
- It is powered by a 18V LXT lithium-ion battery cartridge, which provides long runtime and fast charging.
- The tool is lightweight and compact for easy handling.
- It comes with a variety of accessories, including a chuck key, a bit holder, and a carrying case.
I hope this manual has been helpful. Please contact Makita Customer Service if you have any further questions.
Comments
Post a Comment